On their website they say they do, but I understand it's very different than when Mallory was there
Search found 36 matches
- Thu Jan 05, 2023 1:24 am
- Forum: U.S. Military Krags
- Topic: Springfield Research Service 4 Volumes
- Replies: 23
- Views: 49384
- Wed Jan 04, 2023 3:59 pm
- Forum: U.S. Military Krags
- Topic: Springfield Research Service 4 Volumes
- Replies: 23
- Views: 49384
Re: Springfield Research Service 4 Volumes
Whig - Thank you for bringing this back up. Researching - when there's a trail - is a joy. Thank you again. I do believe I'll hold off on any posts until I have my carbine in hand, but hope to have some good information laid out by then. I DID find that the Lt Gignoux, who led the First Nev Vol Cav ...
- Tue Nov 29, 2022 5:34 am
- Forum: Sporterized and unofficial modified Krags
- Topic: Redfield Peep Screw for side plate
- Replies: 2
- Views: 851
Re: Redfield Peep Screw for side plate
Thank you for linking this picture here and your PM!!! I read about this but hadn't seen the comparison picture.
- Tue Nov 29, 2022 4:22 am
- Forum: Sporterized and unofficial modified Krags
- Topic: Redfield Peep Screw for side plate
- Replies: 2
- Views: 851
Redfield Peep Screw for side plate
Hey all, am trying to find a new screw to work for the sideplate and sight with a Krag Redfield 70KH peep. I understand it's a .187x26tpi screw - and that there are a handful of Krag and 1903 springfield screws that are the same. I don't want to order the wrong thing.... I found this: https://www.li...
- Mon Nov 28, 2022 11:15 pm
- Forum: U.S. Military Krags
- Topic: Krag Board of Ordnance Rifle
- Replies: 19
- Views: 3256
Re: Krag Board of Ordnance Rifle
I dont know, but I was drooling over a couple of them.
- Fri Jun 19, 2020 3:52 am
- Forum: Ammunition, reloading, shooting, etc
- Topic: Chamber differences and tough to close bolt
- Replies: 24
- Views: 7038
Re: Chamber differences and tough to close bolt
I love this place!
- Thu Jun 18, 2020 3:08 am
- Forum: Ammunition, reloading, shooting, etc
- Topic: Chamber differences and tough to close bolt
- Replies: 24
- Views: 7038
Re: Chamber differences and tough to close bolt
Thank you all for the input. I'll keep it ALL in mind when I finally get the rifle back out to shoot.<br /><br />In the meantime, I ordered a single stage cast iron Lee press today (my regular press is the classic turret which is a cast iron base but the turret is milled aluminum and the turret ring...
- Wed Jun 17, 2020 3:20 pm
- Forum: Ammunition, reloading, shooting, etc
- Topic: Chamber differences and tough to close bolt
- Replies: 24
- Views: 7038
Re: Chamber differences and tough to close bolt
Fred, I appreciate the time responding! <br /><br />The cases were a mix. The R-P had been loaded previously, but I do NOT know how many times. I doubt many. They were a gift with the rifle from a dear uncle.<br /><br />The Winchester cases were from a box of ammo that was fired once (some in the ri...
- Wed Jun 17, 2020 2:34 pm
- Forum: Ammunition, reloading, shooting, etc
- Topic: Chamber differences and tough to close bolt
- Replies: 24
- Views: 7038
Re: Chamber differences and tough to close bolt
Butlers - Both the rifle and cut down are 1898 ALTHOUGH the bolt in the carbine is a 1896. So it certainly could be a tighter headspace, although that would mean the 1898 bolt in the 1898 rifle is holding the shell rim further away from the chamber - as the 1898 closed easily and the 1896 met resist...
- Tue Jun 16, 2020 9:42 pm
- Forum: Ammunition, reloading, shooting, etc
- Topic: Chamber differences and tough to close bolt
- Replies: 24
- Views: 7038
Re: Chamber differences and tough to close bolt
Hey Fred, thank you.<br /><br />I suppose I could try a different die. I had two shell holders, both produced the same results, so I sanded one and mic'd the edges to make sure I was "flat". That produced a shell that was pressed further into the die and perhaps moved the shoulder a little...