Creeping along: Next steps are to final shape stock tip, match wood color, and to 'patina' barrel-band and spring.
This 'cut-down' stock is an inch shorter than a true model 1896 Krag carbine stock.
A regular Krag 'band-spring' would have compromised the stock tip.
I improvised a shorter replacement spring from an Argentine Mauser spring, that I had in my junk box.
Besides, everything works better with a Mauser part on it!
A work in progress
- butlersrangers
- Posts: 9910
- Joined: Wed Oct 07, 2009 11:35 pm
- Location: Below the Bridge, Michigan
-
- Posts: 368
- Joined: Fri Feb 05, 2016 11:42 pm
Re: A work in progress
Nice job, a good wood match. I shortened a band spring for my 1873/76 carbine build.
Re: A work in progress
Looking good. This may be something you already know. But I've done some stock finishing (flintlocks I've built) and refinishing of old guns. Used True Oil a lot, because that is what I knew in the early years. Now I realize that the old tried and true boiled linseed oil is the way to go. I ran across this video and it has a few nuances that I'll need to try next time, especially the sanding and going right to the oil application without wiping the "sawdust" off. Thought this may be useful, unless you already have this down. The video even uses a Krag (sporterized) for an example.
https://www.youtube.com/watch?v=mzVdsln29o8
https://www.youtube.com/watch?v=mzVdsln29o8
- butlersrangers
- Posts: 9910
- Joined: Wed Oct 07, 2009 11:35 pm
- Location: Below the Bridge, Michigan
Re: A work in progress
Pretty much finished except for more coats of Linseed Oil.
Not Springfield Armory quality, but, better than Bubba.
I can use this "Faux '96 carbine" without guilt of putting wear and tear on a Safe Queen.
No "saddle-ring", but IMHO, they just get in the way, make noise, and weaken the stock.
I leaving the 1903 front-sight, so future collectors know it's a 'parts project' gun.
Knute, thanks for the stock finish video, some useful ideas there.
This was a fun project and (FWIW) shows there is enough wood in a 'duffle-cut' model 1898 stock to make an imitation model 1896 carbine stock.
(The stock I started with was only 29 inches long, so it is a bit off at the forearm tip).
Not Springfield Armory quality, but, better than Bubba.
I can use this "Faux '96 carbine" without guilt of putting wear and tear on a Safe Queen.
No "saddle-ring", but IMHO, they just get in the way, make noise, and weaken the stock.
I leaving the 1903 front-sight, so future collectors know it's a 'parts project' gun.
Knute, thanks for the stock finish video, some useful ideas there.
This was a fun project and (FWIW) shows there is enough wood in a 'duffle-cut' model 1898 stock to make an imitation model 1896 carbine stock.
(The stock I started with was only 29 inches long, so it is a bit off at the forearm tip).
Re: A work in progress
Are you wearing two different slippers? Very practical but I thought this was a socks only forum.
But I like what you did for the Krag. I have a carbine that the tip was cut off under the band but the guy must have had a change of heart and tried to glue it back on. The spring is couple of hairs short of being right and will not keep the band secured.
I am thinking 2021 is when I can get to it.
.
But I like what you did for the Krag. I have a carbine that the tip was cut off under the band but the guy must have had a change of heart and tried to glue it back on. The spring is couple of hairs short of being right and will not keep the band secured.
I am thinking 2021 is when I can get to it.
.
Deacon in the Church of the Mighty Krag. Member of PETA (People Eating Tasty Animals). Liberty Works Radio
- psteinmayer
- Posts: 2692
- Joined: Tue Aug 30, 2011 2:31 am
Re: A work in progress
Looks great Chuck!