When I cycle dummy rounds through the rifle, sometimes a round will get hung up, nose down. The magazine follower spring seems to be in good shape so I cannot figure out what is causing this.,
Any advice is most welcome. Thanks, Bill
Rounds hanging up in Krag 1898
Re: Rounds hanging up in Krag 1898
The first thing to check is always the magazine cut off. If missing or modified it will cause problems and or damage the cases.
Not sure if any one here has a list of similar threads, a lot can be learned by reviewing the other similar problems and solutions. Using the search function will find many of them but specific wording will catch or miss a lot of the threads. Using google or Yahoo search with KCA in the search line will find even more references.
Not sure if any one here has a list of similar threads, a lot can be learned by reviewing the other similar problems and solutions. Using the search function will find many of them but specific wording will catch or miss a lot of the threads. Using google or Yahoo search with KCA in the search line will find even more references.
Re: Rounds hanging up in Krag 1898
The magazine cut-off is functioning properly, I think I will try a new spring and see if that solves the issue.
Thanks, Bill
Thanks, Bill
BillBlab
- butlersrangers
- Posts: 9881
- Joined: Wed Oct 07, 2009 11:35 pm
- Location: Below the Bridge, Michigan
Re: Rounds hanging up in Krag 1898
'BillBlab' - Welcome to the KCA Forum.
The 'truth be told' the U.S. Krag was designed to feed cartridges with a 220 grain Round-Nosed Bullet, seated to an approximate, 3.089 inch, over-all length.
The position and slope of the case-shoulder, also plays a role in the smooth feed of cartridges.
Many U.S. Krags are tolerant of different bullet profiles and shorter over-all cartridge length.
Sometimes changing the left side-plate can make a Krag more tolerant in feeding non-standard rounds.
When a cartridge is 'short', it may move forward in the magazine. When the bolt makes contact, with the rim of a cartridge that is too far forward, the case shoulder can hang up on the lobe on the interior of the side-plate.
This can cause a jam or the cartridge to 'dive'.
Bullet profiles, like 'Spitzers', can hang up on the rear edge of the barrel-breech.
Some Krags seem to eat anything.
Tell us more about your 'dummy' rounds.
Pictures of everything always helps solve a problem.
The 'truth be told' the U.S. Krag was designed to feed cartridges with a 220 grain Round-Nosed Bullet, seated to an approximate, 3.089 inch, over-all length.
The position and slope of the case-shoulder, also plays a role in the smooth feed of cartridges.
Many U.S. Krags are tolerant of different bullet profiles and shorter over-all cartridge length.
Sometimes changing the left side-plate can make a Krag more tolerant in feeding non-standard rounds.
When a cartridge is 'short', it may move forward in the magazine. When the bolt makes contact, with the rim of a cartridge that is too far forward, the case shoulder can hang up on the lobe on the interior of the side-plate.
This can cause a jam or the cartridge to 'dive'.
Bullet profiles, like 'Spitzers', can hang up on the rear edge of the barrel-breech.
Some Krags seem to eat anything.
Tell us more about your 'dummy' rounds.
Pictures of everything always helps solve a problem.
Re: Rounds hanging up in Krag 1898
Your excellent reply provided the clue. The dummy rounds are a bit shorter than the live rounds. The live rounds are exactly the correct length with the round head.
I'll bet they will work just fine at the range.
At least I have verified that all the inner workings are doing their job.
Thanks very much. Bill
I'll bet they will work just fine at the range.
At least I have verified that all the inner workings are doing their job.
Thanks very much. Bill
BillBlab