I bought this rifle last summer, and am just getting around to loading some ammunition for it. Based on a recommendation from someone on this forum, I bought some .303 British cases and resized them in a 30-40 die. I tried chambering a couple of the empty cases, and there is something in the chamber that makes closing the bolt difficult, and when I extract the case the shoulder is partially crushed all the way around. When I remove the bolt & shine a light in, there's a ring of some light-colored material around the shoulder area of the chamber. I can't get it loose with a wire chamber brush nor, can I scrape anything loose with a screwdriver blade.
Any idea what this could be, and how to clear it out? Could it be bullet lube residue from lead bullets? Do I need to take it to a gunsmith with a chamber reamer to try & clean it out? Any thoughts would be appreciated.
Chamber Obstruction in 1898 Krag Rifle
Re: Chamber Obstruction in 1898 Krag Rifle
Can you photograph the area? Maybe a drill rifle someone unplugged?
- Dick Hosmer
- Posts: 2292
- Joined: Sun Nov 20, 2005 4:11 pm
Re: Chamber Obstruction in 1898 Krag Rifle
Certainly not the least expensive, but I'd think that CAREFULLY reaming the chamber would be the safest way - much better than hammering on a screwdriver!
Re: Chamber Obstruction in 1898 Krag Rifle
Sounds like something unusual was repeatedly shot in the Krag to build up this residue ring. I would suspect blank cartridges that may have done this. Just a suspicion possibility. Needs reamed out and the bore needs to be examined well. How does the bore look to you? Has it possibly been re-chambered for another caliber?
I've never been a fan of re-sizing .303 for the Krag. The case is shorter and it can cause other issues if not done exactly right. If you can get any regular .30-40 Krag ammunition and chamber one, it would be interesting to see if the same problem exists. Sounds like it would if there is a residue ring built up but we like to consider all variables like the brass you made.
Keep us informed. More pictures and info would help. Good luck!
I've never been a fan of re-sizing .303 for the Krag. The case is shorter and it can cause other issues if not done exactly right. If you can get any regular .30-40 Krag ammunition and chamber one, it would be interesting to see if the same problem exists. Sounds like it would if there is a residue ring built up but we like to consider all variables like the brass you made.
Keep us informed. More pictures and info would help. Good luck!
Re: Chamber Obstruction in 1898 Krag Rifle
Dick Hosmer wrote: ↑Wed Nov 15, 2023 4:40 am Certainly not the least expensive, but I'd think that CAREFULLY reaming the chamber would be the safest way - much better than hammering on a screwdriver!
No problem a bigger hammer can't resolve..... so sayeth the Book of the Corps chapter 20 verse 20
Re: Chamber Obstruction in 1898 Krag Rifle
This, or something similar is worth it's price. can be used from .22 and up.
https://www.amazon.com/Teslong-Borescop ... hdGY&psc=1
https://www.amazon.com/Teslong-Borescop ... hdGY&psc=1
- butlersrangers
- Posts: 9909
- Joined: Wed Oct 07, 2009 11:35 pm
- Location: Below the Bridge, Michigan
Re: Chamber Obstruction in 1898 Krag Rifle
I recommended using reformed .303 Brass in the absence of having any .30-40 Brass.
With a chamber problem, I would recommend taking your Krag to a very experienced gunsmith or doing a cerrosafe chamber-cast.
If there is part of a separated case-neck lodged in your chamber, the chamber-cast will likely bond to it.
When the casting is knocked out of the barrel-chamber, the fragment hopefully would be attached to the casting.
I have no way of knowing your resources or mechanical competence.
With a chamber problem, I would recommend taking your Krag to a very experienced gunsmith or doing a cerrosafe chamber-cast.
If there is part of a separated case-neck lodged in your chamber, the chamber-cast will likely bond to it.
When the casting is knocked out of the barrel-chamber, the fragment hopefully would be attached to the casting.
I have no way of knowing your resources or mechanical competence.
Re: Chamber Obstruction in 1898 Krag Rifle
Yeah, DCR. You need to see a gunsmith on this one. Like the Hippocratic Oath says. Do no harm. Common hand tools could do a lot of damage.
Would you have a pic of one of those crushed cases for us to have a looky-see?
Would you have a pic of one of those crushed cases for us to have a looky-see?
Deacon in the Church of the Mighty Krag. Member of PETA (People Eating Tasty Animals). Liberty Works Radio
- Parashooter
- Posts: 707
- Joined: Thu Feb 04, 2010 5:14 am
- Location: Kragmudgeon House, CT
Re: Chamber Obstruction in 1898 Krag Rifle
At this point it seems an obstruction is less likely than the .303 cases not being sized enough to push the shoulder aft enough for the Krag chamber. Neck sizing die won't do that job, of course. If using a FL sizer, be sure that the case enters the die fully during sizing, with no gap between die and shellholder.
The original .303 shoulder is just enough forward to make for hard chambering in the Krag.
The original .303 shoulder is just enough forward to make for hard chambering in the Krag.
Re: Chamber Obstruction in 1898 Krag Rifle
Anyone else remember this old thread?
http://www.kragcollectorsassociation.co ... %27s+cases
After resizing the 303 cases in a good 30/40 die you would think they would chamber. Do we know for sure the die is really setting the shoulder back?
Could the light colored material DCR is seeing in the shoulder be part of a case than came unglued and is now stuck in the chamber? Not sure that is even possible, but I thought I would ask.
Does a new unfired Remington case fit?
http://www.kragcollectorsassociation.co ... %27s+cases
After resizing the 303 cases in a good 30/40 die you would think they would chamber. Do we know for sure the die is really setting the shoulder back?
Could the light colored material DCR is seeing in the shoulder be part of a case than came unglued and is now stuck in the chamber? Not sure that is even possible, but I thought I would ask.
Does a new unfired Remington case fit?