Search found 130 matches

by Century2
Wed Feb 13, 2013 1:06 pm
Forum: Older threads
Topic: Front sight pin
Replies: 3
Views: 2654

Re: Front sight pin

Pin should be slightly less than 1/16 diameter (0.060" I believe) however many have been ramrodded with an unpolished 1/16 punch so 0.0625 or more may be necessary. I prefer using mild spring steel to fabricate my pins so I use hairpin cotters available at the local hardware store. Historically...
by Century2
Mon Feb 11, 2013 12:58 am
Forum: Older threads
Topic: Barrel Asterisk at 6 O'Clock?
Replies: 0
Views: 1235

Barrel Asterisk at 6 O'Clock?

<r>1902 Rifle No. 393120 - Has asterisk stamp on barrel just ahead of the receiver at 6 O'clock in addition to the firing proof. Over the years, I've seen tons of inspector's marks on the receiver, receiver parts, bolt, etc. however not typically on the barrel. Any ideas?<IMG src="https://kragcollec...
by Century2
Sat Dec 29, 2012 6:44 pm
Forum: Older threads
Topic: Original Rifle Cost 1898-1903
Replies: 2
Views: 2479

Re: Original Rifle Cost 1898-1903

Finally got a copy of Mallory's book. Page 98 says the original cost of rifle manufacture was $19.75. Per some inflation/interest calulators I found on the web: What cost $19.75 in 1898 would cost $537.76 in 2012. Now if you had saved $19.75 in 1898 (and picked a bank that never failed), at an inter...
by Century2
Tue Dec 18, 2012 12:33 pm
Forum: Older threads
Topic: Curious ebay picture with Krag
Replies: 5
Views: 3127

Re: Curious ebay picture with Krag

In Norwegian (per Google Translate): fin link til historien (nice link to history)! ;)
by Century2
Thu Dec 13, 2012 12:48 pm
Forum: Older threads
Topic: Krag bolt problem- please help
Replies: 16
Views: 9366

Re: Krag bolt problem- please help

Your best bet is to try another bolt. If this is not an option, verify your bolt is not slightly bent by gauging it with a straight edge all around. I had a Krag that was apparently dropped on its topside when the bolt was fully extended. The "bend" could be inperceptible to the naked eye ...
by Century2
Mon Dec 10, 2012 12:38 pm
Forum: Older threads
Topic: missing the mag. cutoff on my 98
Replies: 6
Views: 4470

Re: missing the mag. cutoff on my 98

I've got just what you need - for postage. Sent you a message (see top of page).
by Century2
Sun Dec 09, 2012 1:22 pm
Forum: Older threads
Topic: missing the mag. cutoff on my 98
Replies: 6
Views: 4470

Re: missing the mag. cutoff on my 98

The shaft of the cutoff when installed and in the on position has a flat on one side that aligns with the wall of the magazine raceway for a flush condition. When installed and in the off position, the flat is rotated into the receiver body and the round side of the shaft enters the magazine raceway...
by Century2
Sat Nov 03, 2012 12:02 pm
Forum: Older threads
Topic: I've previously owned Krags but,
Replies: 12
Views: 8500

Re: I've previously owned Krags but,

COAL is as published in the Load Book. I figure the length over 3 is to get the pointier bullets closer to the rifling. With the various types of rifling wear, the original krag barrels will vary in regards to closeness. Haven't yet encountered any resistance when they are chambered and I have used ...
by Century2
Fri Nov 02, 2012 5:21 pm
Forum: Older threads
Topic: High serial number
Replies: 23
Views: 11191

Re: High serial number

<r>No doubt on this one. 482720 - GB # 309737661.<IMG src="https://kragcollectorsassociation.org/kca/phpBB3/images/yabbfiles/Attachments/pix913746424.jpg"><s>[img]</s><URL url="https://kragcollectorsassociation.org/kca/phpBB3/images/yabbfiles/Attachments/pix913746424.jpg"><LINK_TEXT text="https://kr...
by Century2
Fri Nov 02, 2012 5:16 pm
Forum: Older threads
Topic: High serial number
Replies: 23
Views: 11191

Re: High serial number

<r>The possible 487808 was GB 307426136. I think this image is better?<IMG src="https://kragcollectorsassociation.org/kca/phpBB3/images/yabbfiles/Attachments/Untitled.jpg"><s>[img]</s><URL url="https://kragcollectorsassociation.org/kca/phpBB3/images/yabbfiles/Attachments/Untitled.jpg"><LINK_TEXT tex...